All over Lake County, worn bathtubs are resurfaced in place: repairs first, gloss second, fresh caulk on the way out.
One number reaches the technician who would hold the gun. The figure comes on the call, not after a visit.
(866) 951-0558The voice on the line belongs to the trade, not to a switchboard reading a script. Two minutes of plain description are enough to price a standard tub.
Are you tired of staring at that stained and chipped washing basin in your bathroom? Fixing this eyesore without spending a fortune is totally possible right now.
Instead of a messy tear-out, you can hire a local pro to spray a fresh acrylic coating over the entire shell. This smart service saves you tons of cash and stops you from dealing with months of destructive demolition dust.
First off, the technician scrubs every square inch of your porcelain or fiberglass fixture with heavy-duty chemical etching agents. Removing soap scum and mineral deposits lets the primer bond permanently to the old material without peeling later.
Next, they mask off your tiles and surrounding walls using thick plastic sheeting to catch any stray droplets. Protecting your bathroom floors gives you immense peace of mind while the crew works their magic with specialized spray guns.
Following that prep work, the contractor applies several layers of high-grade aliphatic polyurethane or specialized epoxy resins. This tough barrier gives you a brand-new looking basin that resists daily wear and tear for many years.
Curing times usually take about twenty-four hours before you can safely fill the tub with warm water again. Following these simple steps lets you enjoy a gorgeous bathing spot without the massive renovation headache.
| Method | Estimated Cost | Time Required | Mess Level | |
|---|---|---|---|---|
| Full Replacement | High | Multiple Weeks | Extreme | |
| Surface Coating | Low | One Single Day | Minimal |
Looking at this handy chart helps you see why spraying your fixture makes total financial sense. Choosing the faster route means you get your bathroom back almost immediately.
Living out here in the gorgeous landscapes of Lake County means we appreciate keeping our houses looking sharp and functional. Residents spread across the local ZIP codes frequently deal with hard water that ruins standard plumbing fixtures over time.
Properties with a median household income similar to ours benefit greatly from cost-effective home improvements that stretch every dollar. Bringing in an experienced tradesperson ensures your vintage bathroom features get restored rather than sent to a crowded landfill.
Working with a dedicated regional specialist guarantees you get personalized attention from the first phone call to the final inspection. Backing up our craftsmanship with solid warranties gives you total confidence in the durability of your newly coated basin.
Equally important, our crew cleans up the workspace completely before leaving your property so you never have to lift a finger. This thoughtful approach ensures your daily routine faces zero disruption while your bathroom gets a much-needed makeover.
Many folks wonder if the new finish will peel off after a few months of heavy family use. Applying industrial-grade bonding agents ensures the coating stays firmly attached for a decade or longer with basic cleaning care.
Another frequent concern involves the strong chemical smells produced during the spraying application phase. Proper ventilation fans clear out the fumes quickly so your indoor air quality remains fresh and safe.
Now is the absolute best moment to transform your outdated bathroom without emptying your savings account. Reaching out for professional help takes only a minute of your busy day.
Requesting a zero-cost estimate lets you plan your budget accurately without any hidden fees or high-pressure sales tactics. Taking this simple action puts you one step closer to enjoying a pristine and gorgeous bathing space every single morning.
Three quiet stages carry the whole result. They are also the ones nobody sees in the after photo.
Stage 1 of 3
A reglaze fails or lasts on what happens before the gun comes out. The old surface gets scrubbed of soap film and silicone, etched or primed so the new material has something to grip, then wet sanded until it feels like fine paper. Skip any of that and the prettiest coat in the world lets go within a year, which is exactly the story most peeling tubs tell us.
Stage 2 of 3
Chips, rust blooms and worn drain rings are ground back to sound material and rebuilt with polyester filler, then sanded flush until a fingertip cannot find the spot. Coating over damage only photographs well on day one; a repair you cannot feel is what keeps the finish honest for years.
Stage 3 of 3
The topcoat goes on in fine sprayed passes with an extractor pulling air out the window the whole time. Sprayed layers flow together into one even skin, which is why the result reads as gloss rather than as paint. Brushes and rollers leave the texture that gives cheap refinishing its reputation.
Three real ways out of a worn tub. We only do the first one, so the other two columns are simply what we would tell a friend.
| The question | Reglazing in place | Acrylic liner | Full replacement |
|---|---|---|---|
| What a standard tub costs | $350 to $800 | $1,600 to $4,000 | $3,000 to $10,000 once walls and plumbing join in |
| Bathroom out of action | One day, then the cure | Weeks of lead time, then a fitting day | One to two weeks of trades |
| Demolition involved | None at all | None, but the old tub is sealed inside | Walls opened, floor patched, debris hauled |
| Honest life expectancy | Five years and up when cared for | Long, unless water creeps between the shells | Decades |
| Watch out for | Prep shortcuts by cut-rate crews | A spongy feel and hidden moisture | The budget doubling mid-project |
If your tub is cracked through, actively leaking underneath, or you simply want a different fixture, reglazing is the wrong tool, a verdict you will hear on the very first call.
Pass 1
Soap scum, silicone and old wax stripped, then the surface etched or bonded so the coating can bite.
Pass 2
Every ding ground out, filled and sanded flush. The repairs disappear under the coating instead of through it.
Pass 3
Tile, faucet, floor and glass papered off. Overspray lands on masking paper, never on grout or chrome.
Pass 4
Primer, then gloss coats laid on in thin passes until the surface reads as one poured skin.
Pass 5
The finish hardens on its own clock, 24 to 48 hours. We tape the door and leave the tub in peace.
Pass 6
Old caulk goes out with the old finish. A new mildew-resistant bead seals tub to tile on the way out.
A reglazed tub is your old tub wearing a professional coating. That is a fine thing to be, as long as everyone knows it going in.
A sprayed acrylic urethane skin, bonded to prepared porcelain, steel or fiberglass. It is smooth, glossy, warm to the touch and fully waterproof. Done properly it gives five years and more of daily service, and plenty of our tubs sail well past that with nothing but gentle cleaning.
It is not factory enamel fired onto iron at kiln temperatures, and no honest refinisher will tell you otherwise. It can be scratched by grit, dulled by harsh powders and lifted by standing water in a spot where caulk has failed. It is a durable coating, not a new tub, and it is priced like one.
Two minutes
ZIP, what the tub is made of, what bothers you about it. Said out loud it goes faster than typing, and a photo can follow later if the case is odd.
The same call
The technician who would do the work asks his questions and names a firm figure for a standard job, then confirms it in writing before any van is booked.
You set the date
One van, one technician, drop cloths from the front door to the bathroom. Water off for nothing; only the tub is out of service.
Most of that day
Damage filled and sanded, the room masked, extractor running, then the primer and gloss coats go on in thin, even passes.
24 to 48 hours
The finish hardens untouched, the new caulk bead goes in, and you run the first bath knowing exactly what was done and what to expect of it.
| What we quote | Typical range | Reading the number |
|---|---|---|
| Standard bathtub, reglazed complete | $350 - $800 | Clean, etch, repairs, sprayed gloss and fresh caulk. |
| Chip or rust repair alone | $150 - $300 | When the finish is sound and only one wound needs closing. |
| Clawfoot tub, inside and out | $700 - $1,300 | Two surfaces, more masking, and paint-grade feet if you wish. |
| Shower pan or base | $300 - $550 | Same process on the floor you stand on every morning. |
| Caulk renewal with the job | $90 - $180 | Old bead cut out, mildew-resistant line laid in. |
| Small job minimum | around $250 | The van, the materials and the cure time exist even for tiny work. |
Heavy previous coatings that must be stripped, unusual colors and badly pitted iron push a job toward the top of its bracket. The written price reaches you before the van is even loaded, and it holds.
Ventilation is not a courtesy, it is part of the job. The extractor runs from the first solvent wipe to the last sprayed pass, pulling air out the window instead of through your hallway, and the technician wears supplied air even when the household has gone out for the day. By the evening the bathroom smells like a bathroom again.
The materials are the professional two-part systems made for this trade, mixed fresh on site, never the single-can kits sold next to the paint rollers. It is the difference between a finish that cures into a hard skin and one that stays soft enough to peel at the drain within a season, and it is most of the reason our work carries a written workmanship promise against peeling and loss of adhesion.
And the schedule respects the cure. We tell you in writing when the tub goes back into service, 24 hours for most jobs and 48 for the cautious ones, because handing a family a beautiful surface and letting them ruin it that same night helps nobody. If anything in our workmanship lets go early, the technician comes back and makes it right without a discussion about whose fault the water was.
Strong while spraying, gone surprisingly fast. The extractor vents the room to the outside for the whole job, so the rest of the home stays livable, and by the next morning the odor has left with the fumes. Pregnant households and bird owners get the frank version of this talk before booking.
Between 24 and 48 hours after the final coat, and the exact time is written on the paperwork you keep. The first bath is not a gamble; it is a date.
Any color. The most common request is retiring an avocado, pink or almond tub to white, and the coating is tinted before it is sprayed, so the new color is in the material rather than painted over it.
Yes. The prep changes, the primer changes, the result reads the same. Fiberglass with soft, flexing spots gets extra reinforcement talk first, because coating a moving floor is how warranties die.
Now the old coating comes fully off, which is honest work we price plainly, and then the job proceeds as if the tub had never been touched. Peeling almost always means the first crew skipped the etch or sprayed over silicone, not that your tub rejects coatings.
Five years is the floor we are comfortable promising out loud, not the ceiling. With soft cleaners, no standing mats and caulk kept sound, these finishes routinely serve a decade. What we refuse to do is whisper twenty and hope you lose our number.
Zoom for the lay of the land; the link lists further down name every community the van reaches from here.
Somewhere under that worn surface is the tub you chose. One day brings it back.
Call (866) 951-0558